patch-2.3.14 linux/drivers/isdn/hisax/bkm_ax.h

• Lines: 134
• Date: Thu Aug 12 09:42:33 1999
• Orig file: v2.3.13/linux/drivers/isdn/hisax/bkm_ax.h
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.3.13/linux/drivers/isdn/hisax/bkm_ax.h linux/drivers/isdn/hisax/bkm_ax.h
@@ -0,0 +1,133 @@
+/* $Id: bkm_ax.h,v 1.2 1999/07/01 08:07:55 keil Exp $
+ * bkm_ax.h   low level decls for T-Berkom cards A4T and Scitel Quadro (4*S0, passive)
+ *
+ * Author     Roland Klabunde (R.Klabunde@Berkom.de)
+ *
+ * $Log: bkm_ax.h,v $
+ * Revision 1.2  1999/07/01 08:07:55  keil
+ * Initial version
+ *
+ *
+ *
+ */
+
+#ifndef	__BKM_AX_H__
+#define	__BKM_AX_H__
+
+/* Supported boards	(subtypes) */
+#define SCT_1		1
+#define	SCT_2		2
+#define	SCT_3		3
+#define	SCT_4		4
+#define BKM_A4T		5
+
+
+/* A4T																*/
+#define I20_DEVICE_ID       	0x6120  /* I20 PCI device ID */
+#define I20_VENDOR_ID       	0x11DE  /* I20 PCI vendor ID */
+#define	A4T_SUBVEN_ID		0x0871	
+#define	A4T_SUBSYS_ID		0xFFA4
+/* Scitel Quadro 																*/
+#define	PLX_DEVICE_ID		0x9050	/* Scitel Quadro PLX */
+#define	PLX_VENDOR_ID		0x10B5
+#define	SCT_SUBVEN_ID		0x0871
+#define	SCT_SUBSYS_ID		0xFFA8
+
+
+#define	PLX_ADDR_PLX		0x14	/* Addr PLX configuration */
+#define	PLX_ADDR_ISAC		0x18	/* Addr ISAC */
+#define	PLX_ADDR_HSCX		0x1C	/* Addr HSCX */
+#define	PLX_ADDR_ALE		0x20	/* Addr ALE */
+#define	PLX_ADDR_ALEPLUS	0x24	/* Next Addr behind ALE */
+
+#define	PLX_SUBVEN		0x2C	/* Offset SubVendor */
+#define	PLX_SUBSYS		0x2E	/* Offset SubSystem */
+
+
+/* Application specific registers I20 (Siemens SZB6120H) */
+typedef	struct {
+		/* Video front end horizontal configuration register */
+	volatile u_int	i20VFEHorzCfg;	/* Offset 00 */
+		/* Video front end vertical configuration register */
+	volatile u_int	i20VFEVertCfg;	/* Offset 04 */	
+		/* Video front end scaler and pixel format register */
+	volatile u_int	i20VFEScaler;	/* Offset 08 */	
+		/* Video display top register */
+	volatile u_int	i20VDispTop;   	/* Offset 0C */	
+		/* Video display bottom register */
+	volatile u_int	i20VDispBottom;	/* Offset 10 */	
+		/* Video stride, status and frame grab register */
+	volatile u_int	i20VidFrameGrab;/* Offset 14 */	
+		/* Video display configuration register */
+	volatile u_int	i20VDispCfg;	/* Offset 18 */	
+		/* Video masking map top */
+	volatile u_int	i20VMaskTop;	/* Offset 1C */	
+		/* Video masking map bottom */
+	volatile u_int	i20VMaskBottom;	/* Offset 20 */	
+		/* Overlay control register */
+	volatile u_int 	i20OvlyControl;	/* Offset 24 */	
+		/* System, PCI and general purpose pins control register */
+ 	volatile u_int	i20SysControl; 	/* Offset 28 */	
+#define	sysRESET		0x01000000	/* bit 24:Softreset (Low)		*/
+			/* GPIO 4...0: Output fixed for our cfg! */
+#define	sysCFG			0x000000E0	/* GPIO 7,6,5: Input */
+	/* General purpose pins and guest bus control register */
+ 	volatile u_int	i20GuestControl;/* Offset 2C */	
+#define	guestWAIT_CFG	0x00005555	/* 4 PCI waits for all */
+#define	guestISDN_INT_E	0x01000000	/* ISDN Int en (low) */
+#define	guestVID_INT_E 	0x02000000	/* Video interrupt en (low) */
+#define	guestADI1_INT_R	0x04000000	/* ADI #1 int req (low) */
+#define	guestADI2_INT_R	0x08000000	/* ADI #2 int req (low) */
+#define	guestISDN_RES	0x10000000	/* ISDN reset bit (high) */
+#define	guestADI1_INT_S	0x20000000	/* ADI #1 int pending (low) */
+#define	guestADI2_INT_S	0x40000000	/* ADI #2 int pending (low) */
+#define	guestISDN_INT_S	0x80000000	/* ISAC int pending (low) */
+
+#define	g_A4T_JADE_RES	0x01000000	/* JADE Reset (High) */
+#define	g_A4T_ISAR_RES	0x02000000	/* ISAR Reset (High) */
+#define	g_A4T_ISAC_RES	0x04000000	/* ISAC Reset (High) */
+#define	g_A4T_JADE_BOOTR 0x08000000	/* JADE enable boot SRAM (Low) NOT USED */
+#define	g_A4T_ISAR_BOOTR 0x10000000	/* ISAR enable boot SRAM (Low) NOT USED */
+#define	g_A4T_JADE_INT_S 0x20000000	/* JADE interrupt pnd (Low) */
+#define	g_A4T_ISAR_INT_S 0x40000000	/* ISAR interrupt pnd (Low) */
+#define	g_A4T_ISAC_INT_S 0x80000000	/* ISAC interrupt pnd (Low) */
+
+ 	volatile u_int	i20CodeSource;	/* Offset 30 */	
+ 	volatile u_int	i20CodeXferCtrl;/* Offset 34 */	
+ 	volatile u_int	i20CodeMemPtr;	/* Offset 38 */	
+
+  	volatile u_int	i20IntStatus;	/* Offset 3C */	
+ 	volatile u_int	i20IntCtrl;	/* Offset 40 */	
+#define	intISDN		0x40000000	/* GIRQ1En (ISAC/ADI) (High) */
+#define	intVID		0x20000000	/* GIRQ0En (VSYNC)    (High) */
+#define	intCOD		0x10000000	/* CodRepIrqEn        (High) */
+#define	intPCI 		0x01000000	/* PCI IntA enable    (High) */
+
+ 	volatile u_int	i20I2CCtrl;	/* Offset 44					*/	
+} I20_REGISTER_FILE, *PI20_REGISTER_FILE;
+
+/*
+ * Postoffice structure for A4T
+ *
+ */
+#define	PO_OFFSET	0x00000200	/* Postoffice offset from base */
+
+#define	GCS_0		0x00000000 	/* Guest bus chip selects */
+#define	GCS_1		0x00100000
+#define	GCS_2		0x00200000
+#define	GCS_3		0x00300000
+
+#define	PO_READ		0x00000000	/* R/W from/to guest bus */
+#define	PO_WRITE	0x00800000
+
+#define	PO_PEND		0x02000000
+
+#define POSTOFFICE(postoffice) *(volatile unsigned int*)(postoffice)
+
+/* Wait unlimited (don't worry)										*/ 
+#define	__WAITI20__(postoffice)										\
+do {		   	 		   											\
+  	while ((POSTOFFICE(postoffice) & PO_PEND)) ;					\
+} while (0)
+
+#endif	/* __BKM_AX_H__ */