patch-2.3.49 linux/drivers/char/digi1.h

• Lines: 101
• Date: Mon Feb 28 07:16:54 2000
• Orig file: v2.3.48/linux/drivers/char/digi1.h
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.3.48/linux/drivers/char/digi1.h linux/drivers/char/digi1.h
@@ -0,0 +1,100 @@
+/*          Definitions for DigiBoard ditty(1) command.                 */
+
+#if !defined(TIOCMODG)
+#define	TIOCMODG	('d'<<8) | 250		/* get modem ctrl state	*/
+#define	TIOCMODS	('d'<<8) | 251		/* set modem ctrl state	*/
+#endif
+
+#if !defined(TIOCMSET)
+#define	TIOCMSET	('d'<<8) | 252		/* set modem ctrl state	*/
+#define	TIOCMGET	('d'<<8) | 253		/* set modem ctrl state	*/
+#endif
+
+#if !defined(TIOCMBIC)
+#define	TIOCMBIC	('d'<<8) | 254		/* set modem ctrl state */
+#define	TIOCMBIS	('d'<<8) | 255		/* set modem ctrl state */
+#endif
+
+#if !defined(TIOCSDTR)
+#define	TIOCSDTR	('e'<<8) | 0		/* set DTR		*/
+#define	TIOCCDTR	('e'<<8) | 1		/* clear DTR		*/
+#endif
+
+/************************************************************************
+ * Ioctl command arguments for DIGI parameters.
+ ************************************************************************/
+#define DIGI_GETA	('e'<<8) | 94		/* Read params		*/
+
+#define DIGI_SETA	('e'<<8) | 95		/* Set params		*/
+#define DIGI_SETAW	('e'<<8) | 96		/* Drain & set params	*/
+#define DIGI_SETAF	('e'<<8) | 97		/* Drain, flush & set params */
+
+#define	DIGI_GETFLOW	('e'<<8) | 99		/* Get startc/stopc flow */
+						/* control characters 	 */
+#define	DIGI_SETFLOW	('e'<<8) | 100		/* Set startc/stopc flow */
+						/* control characters	 */
+#define	DIGI_GETAFLOW	('e'<<8) | 101		/* Get Aux. startc/stopc */
+						/* flow control chars 	 */
+#define	DIGI_SETAFLOW	('e'<<8) | 102		/* Set Aux. startc/stopc */
+						/* flow control chars	 */
+
+#define	DIGI_GETINFO	('e'<<8) | 103		/* Fill in digi_info */
+#define	DIGI_POLLER	('e'<<8) | 104		/* Turn on/off poller */
+#define	DIGI_INIT	('e'<<8) | 105		/* Allow things to run. */
+
+struct	digiflow_struct 
+{
+	unsigned char	startc;				/* flow cntl start char	*/
+	unsigned char	stopc;				/* flow cntl stop char	*/
+};
+
+typedef struct digiflow_struct digiflow_t;
+
+
+/************************************************************************
+ * Values for digi_flags 
+ ************************************************************************/
+#define DIGI_IXON	0x0001		/* Handle IXON in the FEP	*/
+#define DIGI_FAST	0x0002		/* Fast baud rates		*/
+#define RTSPACE		0x0004		/* RTS input flow control	*/
+#define CTSPACE		0x0008		/* CTS output flow control	*/
+#define DSRPACE		0x0010		/* DSR output flow control	*/
+#define DCDPACE		0x0020		/* DCD output flow control	*/
+#define DTRPACE		0x0040		/* DTR input flow control	*/
+#define DIGI_FORCEDCD	0x0100		/* Force carrier		*/
+#define	DIGI_ALTPIN	0x0200		/* Alternate RJ-45 pin config	*/
+#define	DIGI_AIXON	0x0400		/* Aux flow control in fep	*/
+
+
+/************************************************************************
+ * Values for digiDload
+ ************************************************************************/
+#define NORMAL  0
+#define PCI_CTL 1
+
+#define SIZE8  0
+#define SIZE16 1
+#define SIZE32 2
+
+/************************************************************************
+ * Structure used with ioctl commands for DIGI parameters.
+ ************************************************************************/
+struct digi_struct 
+{
+	unsigned short	digi_flags;		/* Flags (see above)	*/
+};
+
+typedef struct digi_struct digi_t;
+
+struct digi_info 
+{
+	unsigned long board;        /* Which board is this ? */
+	unsigned char status;       /* Alive or dead */
+	unsigned char type;         /* see epca.h */
+	unsigned char subtype;      /* For future XEM, XR, etc ... */
+	unsigned short numports;    /* Number of ports configured */
+	unsigned char *port;        /* I/O Address */
+	unsigned char *membase;     /* DPR Address */
+	unsigned char *version;     /* For future ... */
+	unsigned short windowData;  /* For future ... */
+} ;