Request for Comments: Draft cisco Systems, Inc. cisco MIB* Sun Nov 19 22:27:19 1989 cisco Systems, Inc. 1350 Willow Road Menlo Park, CA 94025 customer-service@cisco.com 1. Introduction This memo describes the variables that are implemented for the cisco Systems, Inc. set of products including the Gateway Server, Terminal Server, Trouter, and Protocol Translator. The document relies upon the Structure of Management Information (SMI), RFC1065. It is presented in a format similar to the Management Information Base for Network Management of TCP/IP-based internets, RFC1066. This document describes the cisco local Management Information Base (MIB) variables for version 8.0 of the system software. 2. Objects Managed objects defined in this MIB are only accessible by the RFC1098 SNMP and are defined using Abstract Syntax Notation One (ASN.1). 2.1. Object Groupings The SMI enterprises subtree was broken up into pieces so each vendor would have a specific location for MIB variables that were either proprietary or unique to their products. cisco was authorized to use the tree starting with the ASN.1 object identifier of 9. The full object identifier path is: *This file is machine generated. Do not edit. cisco MIB [Page 1] Request for Comments: Draft cisco Systems, Inc. 1.3.6.1.4.1.9 The tree below the cisco assigned object identifier is broken up into three groups: - Product names - Local variables - Temporary variables The product name space is reserved for naming products which require an object identifier from the vendor's specific tree. See the RFC1066 MIB variable sysObjectID. The local and temporary variables contain objects which can be monitored or managed by a network management protocol. The local variable space is laid out exactly as specified in RFC1066 as follows: - Local System - Local Interfaces - Local Address Translation - Local IP - Local ICMP - Local TCP - Local UDP - Local EGP Only the groups which have local variables defined will exist in the local variable space. In addition, the following group was added to provide support beyond what RFC1066 provided. - Local Terminal Server The temporary variables are defined as a place to hold objects whose lifetime may only be a single software release. It exists for experimentation purposes and to hold other vendors' objects until that vendor may define their own. These variables are not guaranteed to be preserved for any length of time. 2.2. Format of Definitions This section describes the format of each of the objects within the cisco local MIB. This format is identical to the cisco MIB [Page 2] Request for Comments: Draft cisco Systems, Inc. format used in RFC1066. In fact this entire description was shamelessly cribbed from that RFC's section 4.2. OBJECT: ------- A textual name, termed the OBJECT DESCRIPTOR, for the object type, along with its corresponding OBJECT IDENTIFIER. Syntax: The abstract syntax for the object type, presented using ASN.1. This must resolve to an instance of the ASN.1 type ObjectSyntax defined in the SMI. Definition: A textual description of the semantics of the object type. Implementations should ensure that their interpretation of the object type fulfills this definition since this MIB is intended for use in multi-vendor environments. As such it is vital that object types have consistent meaning across all machines. Access: One of read-only, read-write, write-only, or not- accessible. Status: One of mandatory, optional, or obsolete. 3. Object Definitions CISCO-MIB { iso org(3) dod(6) internet(1) private(4) enterprises(1) 9 } DEFINITIONS ::= BEGIN IMPORTS enterprises, OBJECT-TYPE, NetworkAddress, IpAddress, Counter, Gauge, TimeTicks, OBJECT-TYPE FROM RFC1065-SMI cisco OBJECT IDENTIFIER ::= { enterprises 9 } cisco MIB [Page 3] Request for Comments: Draft cisco Systems, Inc. products OBJECT IDENTIFIER ::= { cisco 1 } local OBJECT IDENTIFIER ::= { cisco 2 } temporary OBJECT IDENTIFIER ::= { cisco 3 } gateway-server OBJECT IDENTIFIER ::= { products 1 } terminal-server OBJECT IDENTIFIER ::= { products 2 } trouter OBJECT IDENTIFIER ::= { products 3 } protocol-translator OBJECT IDENTIFIER ::= { products 4 } lsystem OBJECT IDENTIFIER ::= { local 1 } linterfaces OBJECT IDENTIFIER ::= { local 2 } lat OBJECT IDENTIFIER ::= { local 3 } lip OBJECT IDENTIFIER ::= { local 4 } licmp OBJECT IDENTIFIER ::= { local 5 } ltcp OBJECT IDENTIFIER ::= { local 6 } ludp OBJECT IDENTIFIER ::= { local 7 } legp OBJECT IDENTIFIER ::= { local 8 } lts OBJECT IDENTIFIER ::= { local 9 } decnet OBJECT IDENTIFIER ::= { temporary 1 } xns OBJECT IDENTIFIER ::= { temporary 2 } appletalk OBJECT IDENTIFIER ::= { temporary 3 } novell OBJECT IDENTIFIER ::= { temporary 4 } END 3.1. Product Section The product section contains the different product's object identifiers. Each product has a unique object identifier allocated from this section which is referenced by the sysObjectID variable from RFC1066. Gateway-Server OBJECT IDENTIFIER ::= { products 1 } Terminal-Server OBJECT IDENTIFIER ::= { products 2 } TRouter OBJECT IDENTIFIER ::= { products 3 } Protocol-Translator OBJECT IDENTIFIER ::= { products 4 } New products will be added at the end of this list. 3.2. Local Variable Section This section describes the local variables within the cisco product line. Groups may or may not be present depending on the software options present in the managed device. cisco MIB [Page 4] Request for Comments: Draft cisco Systems, Inc. 3.2.1. Local System Group This group is present in all products. OBJECT: ------- romId { lsystem 1 } Syntax: OCTET STRING Definition: This variable contains a printable octet string which contains the System Bootstrap description and version identification. Access: read-only. Status: mandatory. OBJECT: ------- whyReload { lsystem 2 } Syntax: OCTET STRING Definition: This variable contains a printable octet string which contains the reason why the system was last restarted. Access: read-only. Status: mandatory. OBJECT: ------- hostName { lsystem 3 } cisco MIB [Page 5] Request for Comments: Draft cisco Systems, Inc. Syntax: OCTET STRING Definition: This variable represents the name of the host in printable ascii characters. Access: read-only. Status: mandatory. OBJECT: ------- domainName { lsystem 4 } Syntax: OCTET STRING Definition: This variable is the domain portion of the domain name of the host. Access: read-only. Status: mandatory. OBJECT: ------- authAddr { lsystem 5 } Syntax: NetworkAddress Definition: This variable contains the last SNMP authorization failure IP address. Access: read-only. cisco MIB [Page 6] Request for Comments: Draft cisco Systems, Inc. Status: mandatory. OBJECT: ------- bootHost { lsystem 6 } Syntax: NetworkAddress Definition: Contains the IP address of the host that supplied the currently running software. Access: read-only. Status: mandatory. OBJECT: ------- ping { lsystem 7 } Syntax: INTEGER Definition: Supplies a way to ping a host from this entity. Access: read-write. Status: mandatory. OBJECT: ------- freeMem { lsystem 8 } Syntax: INTEGER cisco MIB [Page 7] Request for Comments: Draft cisco Systems, Inc. Definition: Return the amount of free memory in bytes. Access: read-only. Status: mandatory. OBJECT: ------- bufferElFree { lsystem 9 } Syntax: INTEGER Definition: Contains the number of free buffer elements. Access: read-only. Status: mandatory. OBJECT: ------- bufferElMax { lsystem 10 } Syntax: INTEGER Definition: Contains the maximum number of buffer elements. Access: read-only. Status: mandatory. OBJECT: cisco MIB [Page 8] Request for Comments: Draft cisco Systems, Inc. ------- bufferElHit { lsystem 11 } Syntax: INTEGER Definition: Contains the number of buffer element hits. Access: read-only. Status: mandatory. OBJECT: ------- bufferElMiss { lsystem 12 } Syntax: INTEGER Definition: Contains the number of buffer element misses. Access: read-only. Status: mandatory. OBJECT: ------- bufferElCreate { lsystem 13 } Syntax: INTEGER Definition: Contains the number of buffer element creates. Access: read-only. cisco MIB [Page 9] Request for Comments: Draft cisco Systems, Inc. Status: mandatory. OBJECT: ------- bufferSmSize { lsystem 14 } Syntax: INTEGER Definition: Contains the size of small buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferSmTotal { lsystem 15 } Syntax: INTEGER Definition: Contains the total number of small buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferSmFree { lsystem 16 } Syntax: INTEGER cisco MIB [Page 10] Request for Comments: Draft cisco Systems, Inc. Definition: Contains the number of free small buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferSmMax { lsystem 17 } Syntax: INTEGER Definition: Contains the maximum number of small buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferSmHit { lsystem 18 } Syntax: INTEGER Definition: Contains the number of small buffer hits. Access: read-only. Status: mandatory. OBJECT: cisco MIB [Page 11] Request for Comments: Draft cisco Systems, Inc. ------- bufferSmMiss { lsystem 19 } Syntax: INTEGER Definition: Contains the number of small buffer misses. Access: read-only. Status: mandatory. OBJECT: ------- bufferSmTrim { lsystem 20 } Syntax: INTEGER Definition: Contains the number of small buffer trims. Access: read-only. Status: mandatory. OBJECT: ------- bufferSmCreate { lsystem 21 } Syntax: INTEGER Definition: Contains the number of small buffer creates. Access: read-only. cisco MIB [Page 12] Request for Comments: Draft cisco Systems, Inc. Status: mandatory. OBJECT: ------- bufferMdSize { lsystem 22 } Syntax: INTEGER Definition: Contains the size of medium buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferMdTotal { lsystem 23 } Syntax: INTEGER Definition: Contains the total number of medium buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferMdFree { lsystem 24 } Syntax: INTEGER cisco MIB [Page 13] Request for Comments: Draft cisco Systems, Inc. Definition: Contains the number of free medium buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferMdMax { lsystem 25 } Syntax: INTEGER Definition: Contains the maximum number of medium buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferMdHit { lsystem 26 } Syntax: INTEGER Definition: Contains the number of medium buffer hits. Access: read-only. Status: mandatory. OBJECT: cisco MIB [Page 14] Request for Comments: Draft cisco Systems, Inc. ------- bufferMdMiss { lsystem 27 } Syntax: INTEGER Definition: Contains the number of medium buffer misses. Access: read-only. Status: mandatory. OBJECT: ------- bufferMdTrim { lsystem 28 } Syntax: INTEGER Definition: Contains the number of medium buffer trims. Access: read-only. Status: mandatory. OBJECT: ------- bufferMdCreate { lsystem 29 } Syntax: INTEGER Definition: Contains the number of medium buffer creates. Access: read-only. cisco MIB [Page 15] Request for Comments: Draft cisco Systems, Inc. Status: mandatory. OBJECT: ------- bufferBgSize { lsystem 30 } Syntax: INTEGER Definition: Contains the size of big buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferBgTotal { lsystem 31 } Syntax: INTEGER Definition: Contains the total number of big buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferBgFree { lsystem 32 } Syntax: INTEGER cisco MIB [Page 16] Request for Comments: Draft cisco Systems, Inc. Definition: Contains the number of free big buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferBgMax { lsystem 33 } Syntax: INTEGER Definition: Contains the maximum number of big buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferBgHit { lsystem 34 } Syntax: INTEGER Definition: Contains the number of big buffer hits. Access: read-only. Status: mandatory. OBJECT: cisco MIB [Page 17] Request for Comments: Draft cisco Systems, Inc. ------- bufferBgMiss { lsystem 35 } Syntax: INTEGER Definition: Contains the number of big buffer misses. Access: read-only. Status: mandatory. OBJECT: ------- bufferBgTrim { lsystem 36 } Syntax: INTEGER Definition: Contains the number of big buffer trims. Access: read-only. Status: mandatory. OBJECT: ------- bufferBgCreate { lsystem 37 } Syntax: INTEGER Definition: Contains the number of big buffer creates. Access: read-only. cisco MIB [Page 18] Request for Comments: Draft cisco Systems, Inc. Status: mandatory. OBJECT: ------- bufferLgSize { lsystem 38 } Syntax: INTEGER Definition: Contains the size of large buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferLgTotal { lsystem 39 } Syntax: INTEGER Definition: Contains the total number of large buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferLgFree { lsystem 40 } Syntax: INTEGER cisco MIB [Page 19] Request for Comments: Draft cisco Systems, Inc. Definition: Contains the number of free large buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferLgMax { lsystem 41 } Syntax: INTEGER Definition: Contains the maximum number of large buffers. Access: read-only. Status: mandatory. OBJECT: ------- bufferLgHit { lsystem 42 } Syntax: INTEGER Definition: Contains the number of large buffer hits. Access: read-only. Status: mandatory. OBJECT: cisco MIB [Page 20] Request for Comments: Draft cisco Systems, Inc. ------- bufferLgMiss { lsystem 43 } Syntax: INTEGER Definition: Contains the number of large buffer misses. Access: read-only. Status: mandatory. OBJECT: ------- bufferLgTrim { lsystem 44 } Syntax: INTEGER Definition: Contains the number of large buffer trims. Access: read-only. Status: mandatory. OBJECT: ------- bufferLgCreate { lsystem 45 } Syntax: INTEGER Definition: Contains the number of large buffer creates. Access: read-only. cisco MIB [Page 21] Request for Comments: Draft cisco Systems, Inc. Status: mandatory. OBJECT: ------- bufferFail { lsystem 46 } Syntax: INTEGER Definition: Count of the number of buffer allocation failures. Access: read-only. Status: mandatory. OBJECT: ------- bufferNoMem { lsystem 47 } Syntax: INTEGER Definition: Count of the number of buffer create failures due to no free memory. Access: read-only. Status: mandatory. OBJECT: ------- netConfigIP { lsystem 48 } Syntax: NetworkAddress cisco MIB [Page 22] Request for Comments: Draft cisco Systems, Inc. Definition: Holds the IP address of the host that supplied the network-confg file. Access: read-only. Status: mandatory. OBJECT: ------- netConfigName { lsystem 49 } Syntax: OCTET STRING Definition: Holds the name of the network configuration file. Access: read-only. Status: mandatory. OBJECT: ------- netConfigSet { lsystem 50 } Syntax: OCTET STRING Definition: Permit the loading of a new network-confg file. Access: read-write. Status: mandatory. cisco MIB [Page 23] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- hostConfigIP { lsystem 51 } Syntax: NetworkAddress Definition: Contains the IP address of the host that provided the host-config file. Access: read-only. Status: mandatory. OBJECT: ------- hostConfigName { lsystem 52 } Syntax: OCTET STRING Definition: Contains the name of the last configured host-confg file. Access: read-only. Status: mandatory. OBJECT: ------- hostConfigSet { lsystem 53 } Syntax: OCTET STRING Definition: Permit the loading of a new host-confg file. cisco MIB [Page 24] Request for Comments: Draft cisco Systems, Inc. Access: read-write. Status: mandatory. 3.2.2. Local Interface Group This group is present in all products. 3.2.2.1. Local Interface Table This group provides additional objects to the table defined by RFC1066. OBJECT: ------- lifTable { linterfaces 1 } Syntax: SEQUENCE OF LIfEntry Definition: A list of interface entries. Access: read-only. Status: mandatory. OBJECT: lifEntry { lifTable 1 } Syntax: LIfEntry ::= SEQUENCE { locIfHardType OCTET STRING, locIfLineProt INTEGER, locIfLastIn INTEGER, locIfLastOut cisco MIB [Page 25] Request for Comments: Draft cisco Systems, Inc. INTEGER, locIfLastOutHang INTEGER, locIfInBitsSec INTEGER, locIfInPktsSec INTEGER, locIfOutBitsSec INTEGER, locIfOutPktsSec INTEGER, locIfInRunts INTEGER, locIfInGiants INTEGER, locIfInCRC INTEGER, locIfInFrame INTEGER, locIfInOverrun INTEGER, locIfInIgnored INTEGER, locIfInAbort INTEGER, locIfResets INTEGER, locIfRestarts INTEGER, locIfKeep INTEGER, locIfReason OCTET STRING, } Definition: A collection of additional objects in the cisco interface. Access: read-only. Status: mandatory. cisco MIB [Page 26] Request for Comments: Draft cisco Systems, Inc. The following section describes the components of the table. OBJECT: ------- locIfHardType { lifEntry 1 } Syntax: OCTET STRING Definition: Return the type of interface in printable ascii. Access: read-only. Status: mandatory. OBJECT: ------- locIfLineProt { lifEntry 2 } Syntax: INTEGER Definition: Boolean whether interface line protocol is up or not. Access: read-only. Status: mandatory. OBJECT: ------- locIfLastIn { lifEntry 3 } Syntax: INTEGER Definition: cisco MIB [Page 27] Request for Comments: Draft cisco Systems, Inc. Elapsed time since last successful protocol input packet was received. Access: read-only. Status: mandatory. OBJECT: ------- locIfLastOut { lifEntry 4 } Syntax: INTEGER Definition: Elapsed time since last successful protocol output was was transmitted. Access: read-only. Status: mandatory. OBJECT: ------- locIfLastOutHang { lifEntry 5 } Syntax: INTEGER Definition: Elapsed time since last protocol output packet could not be uccessfully transmited. Access: read-only. Status: mandatory. cisco MIB [Page 28] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- locIfInBitsSec { lifEntry 6 } Syntax: INTEGER Definition: Five minute average of input bits per second. Access: read-only. Status: mandatory. OBJECT: ------- locIfInPktsSec { lifEntry 7 } Syntax: INTEGER Definition: Five minute average of input packets per second. Access: read-only. Status: mandatory. OBJECT: ------- locIfOutBitsSec { lifEntry 8 } Syntax: INTEGER Definition: Five minute average of output bits per second. Access: cisco MIB [Page 29] Request for Comments: Draft cisco Systems, Inc. read-only. Status: mandatory. OBJECT: ------- locIfOutPktsSec { lifEntry 9 } Syntax: INTEGER Definition: Five minute average of output packets per second. Access: read-only. Status: mandatory. OBJECT: ------- locIfInRunts { lifEntry 10 } Syntax: INTEGER Definition: Number of packets input which were smaller then the allowable physical edia permitted. Access: read-only. Status: mandatory. OBJECT: ------- locIfInGiants { lifEntry 11 } cisco MIB [Page 30] Request for Comments: Draft cisco Systems, Inc. Syntax: INTEGER Definition: Number of input packets which were larger then the physical media ermitted. Access: read-only. Status: mandatory. OBJECT: ------- locIfInCRC { lifEntry 12 } Syntax: INTEGER Definition: Number of input packets which had cyclic redundancy checksum errors. Access: read-only. Status: mandatory. OBJECT: ------- locIfInFrame { lifEntry 13 } Syntax: INTEGER Definition: Number of input packet which were misaligned. Access: read-only. cisco MIB [Page 31] Request for Comments: Draft cisco Systems, Inc. Status: mandatory. OBJECT: ------- locIfInOverrun { lifEntry 14 } Syntax: INTEGER Definition: Count of input which arrived too quickly for the to hardware receive. Access: read-only. Status: mandatory. OBJECT: ------- locIfInIgnored { lifEntry 15 } Syntax: INTEGER Definition: Number of input packets which were simply ignored by this interface. Access: read-only. Status: mandatory. OBJECT: ------- locIfInAbort { lifEntry 16 } Syntax: cisco MIB [Page 32] Request for Comments: Draft cisco Systems, Inc. INTEGER Definition: Number of input packets which were aborted. Access: read-only. Status: mandatory. OBJECT: ------- locIfResets { lifEntry 17 } Syntax: INTEGER Definition: Number of times the interface internally reset. Access: read-only. Status: mandatory. OBJECT: ------- locIfRestarts { lifEntry 18 } Syntax: INTEGER Definition: Number of time interface needed to be completely restarted. Access: read-only. Status: mandatory. cisco MIB [Page 33] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- locIfKeep { lifEntry 19 } Syntax: INTEGER Definition: Boolean whether keepalives are enabled on this interface. Access: read-only. Status: mandatory. OBJECT: ------- locIfReason { lifEntry 20 } Syntax: OCTET STRING Definition: Printable ascii reason for interface last status change. Access: read-only. Status: mandatory. 3.2.3. Local IP Group This group is present in all products which are using the IP protocol. 3.2.3.1. Local IP Address Table This group provides additional objects to the table defined by RFC1066. cisco MIB [Page 34] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- lipAddrTable { lip 1 } Syntax: SEQUENCE OF LIpAddrEntry Definition: A list of IP address entries. Access: read-only. Status: mandatory. OBJECT: lipAddrEntry { lipAddrTable 1 } Syntax: LIpAddrEntry ::= SEQUENCE { locIPHow OCTET STRING, locIPWho NetworkAddress, locIPHelper NetworkAddress, locIPSecurity INTEGER, locIPRedirects INTEGER, locIPUnreach INTEGER, } Definition: A collection of additional objects in the cisco IP implementation. Access: read-only. Status: mandatory. cisco MIB [Page 35] Request for Comments: Draft cisco Systems, Inc. The following section describes the components of the table. OBJECT: ------- locIPHow { lipAddrEntry 1 } Syntax: OCTET STRING Definition: Printable ascii method of how this interface obtained its IP address. Access: read-only. Status: mandatory. OBJECT: ------- locIPWho { lipAddrEntry 2 } Syntax: NetworkAddress Definition: IP address of who supplied this interface its IP address. Access: read-only. Status: mandatory. OBJECT: ------- locIPHelper { lipAddrEntry 3 } Syntax: NetworkAddress cisco MIB [Page 36] Request for Comments: Draft cisco Systems, Inc. Definition: IP helper address for broadcast forwarding support. Access: read-only. Status: mandatory. OBJECT: ------- locIPSecurity { lipAddrEntry 4 } Syntax: INTEGER Definition: IP security level. See RFCXXX. Access: read-only. Status: mandatory. OBJECT: ------- locIPRedirects { lipAddrEntry 5 } Syntax: INTEGER Definition: Boolean whether ICMP redirects will be sent or not. Access: read-only. Status: mandatory. OBJECT: cisco MIB [Page 37] Request for Comments: Draft cisco Systems, Inc. ------- locIPUnreach { lipAddrEntry 6 } Syntax: INTEGER Definition: Boolean whether ICMP unreachables will be sent or not. Access: read-only. Status: mandatory. 3.2.3.2. Local IP Routing Table This group provides additional objects to the table defined by RFC1066. OBJECT: ------- lipRoutingTable { lip 2 } Syntax: SEQUENCE OF LIpRouteEntry Definition: A list of IP routing entries. Access: read-only. Status: mandatory. OBJECT: lipRouteEntry { lipRoutingTable 1 } Syntax: LIpRouteEntry ::= SEQUENCE { locRtMask cisco MIB [Page 38] Request for Comments: Draft cisco Systems, Inc. NetworkAddress, locRtCount INTEGER, locRtUses INTEGER, } Definition: A collection of additional objects in the cisco IP routing implementation. Access: read-only. Status: mandatory. The following section describes the components of the table. OBJECT: ------- locRtMask { lipRouteEntry 1 } Syntax: NetworkAddress Definition: Routing table network mask. Access: read-only. Status: mandatory. OBJECT: ------- locRtCount { lipRouteEntry 2 } Syntax: INTEGER Definition: cisco MIB [Page 39] Request for Comments: Draft cisco Systems, Inc. Number of parallel routes within routing table. Access: read-only. Status: mandatory. OBJECT: ------- locRtUses { lipRouteEntry 3 } Syntax: INTEGER Definition: Number of times this route was used in a forward operation. Access: read-only. Status: mandatory. OBJECT: ------- routeFilter { lip 3 } Syntax: INTEGER Definition: A simple routing filter used for testing. Access: read-only. Status: mandatory. OBJECT: cisco MIB [Page 40] Request for Comments: Draft cisco Systems, Inc. ------- actThresh { lip 4 } Syntax: INTEGER Definition: Threshold of IP accounting records in use before IP traffic will be iscarded. Access: read-only. Status: mandatory. OBJECT: ------- actLostPkts { lip 5 } Syntax: INTEGER Definition: Lost IP packets due to memory limitations. Access: read-only. Status: mandatory. OBJECT: ------- actLostByts { lip 6 } Syntax: INTEGER Definition: Total bytes of lost IP packets. Access: cisco MIB [Page 41] Request for Comments: Draft cisco Systems, Inc. read-only. Status: mandatory. 3.2.3.3. Local IP Accounting Table This group provides access to the cisco IP accounting support. OBJECT: ------- lipAccountingTable { lip 7 } Syntax: SEQUENCE OF LIpAccountEntry Definition: A list of IP accounting entries. Access: read-only. Status: mandatory. OBJECT: lipAccountEntry { lipAccountingTable 1 } Syntax: LIpAccountEntry ::= SEQUENCE { actSrc NetworkAddress, actDst NetworkAddress, actPkts INTEGER, actByts INTEGER, } Definition: A collection of objects necessary for IP accounting. cisco MIB [Page 42] Request for Comments: Draft cisco Systems, Inc. Access: read-only. Status: mandatory. The following section describes the components of the table. OBJECT: ------- actSrc { lipAccountEntry 1 } Syntax: NetworkAddress Definition: IP Source address for host traffic matrix. Access: read-only. Status: mandatory. OBJECT: ------- actDst { lipAccountEntry 2 } Syntax: NetworkAddress Definition: IP Destination address for host traffic matrix. Access: read-only. Status: mandatory. OBJECT: ------- cisco MIB [Page 43] Request for Comments: Draft cisco Systems, Inc. actPkts { lipAccountEntry 3 } Syntax: INTEGER Definition: Number of IP packets sent from source to destination. Access: read-only. Status: mandatory. OBJECT: ------- actByts { lipAccountEntry 4 } Syntax: INTEGER Definition: Total number of bytes in IP packets from source to destination. Access: read-only. Status: mandatory. 3.2.4. Local TCP Group This group is present in all products which are using the TCP protocol. 3.2.4.1. Local TCP Connection Table This group provides additional objects to the table defined by RFC1066. OBJECT: cisco MIB [Page 44] Request for Comments: Draft cisco Systems, Inc. ------- ltcpConnTable { ltcp 1 } Syntax: SEQUENCE OF LTcpConnEntry Definition: A list of TCP connection entries. Access: read-only. Status: mandatory. OBJECT: ltcpConnEntry { ltcpConnTable 1 } Syntax: LTcpConnEntry ::= SEQUENCE { loctcpConnInBytes INTEGER, loctcpConnOutBytes INTEGER, loctcpConnInPkts INTEGER, loctcpConnOutPkts INTEGER, loctcpConnElapsed TimeTicks, } Definition: A collection of additional objects in the cisco TCP implementation. Access: read-only. Status: mandatory. cisco MIB [Page 45] Request for Comments: Draft cisco Systems, Inc. The following section describes the components of the table. OBJECT: ------- loctcpConnInBytes { ltcpConnEntry 1 } Syntax: INTEGER Definition: Bytes input for this TCP connection. Access: read-only. Status: mandatory. OBJECT: ------- loctcpConnOutBytes { ltcpConnEntry 2 } Syntax: INTEGER Definition: Bytes output for this TCP connection. Access: read-only. Status: mandatory. OBJECT: ------- loctcpConnInPkts { ltcpConnEntry 3 } Syntax: INTEGER Definition: Packets input for this TCP connection. cisco MIB [Page 46] Request for Comments: Draft cisco Systems, Inc. Access: read-only. Status: mandatory. OBJECT: ------- loctcpConnOutPkts { ltcpConnEntry 4 } Syntax: INTEGER Definition: Packets output for this TCP connection. Access: read-only. Status: mandatory. OBJECT: ------- loctcpConnElapsed { ltcpConnEntry 5 } Syntax: TimeTicks Definition: How long this TCP connection has been established. Access: read-only. Status: mandatory. 3.2.5. Local cisco Terminal Server Group This group is present in all products which contain asynchronous terminal lines. cisco MIB [Page 47] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- tsLines { lts 1 } Syntax: INTEGER Definition: Number of physical lines on this device. Access: read-only. Status: optional. 3.2.5.1. Local Terminal Server Line Table This group contains terminal server specific information on a per line basis. OBJECT: ------- ltsLineTable { lts 2 } Syntax: SEQUENCE OF LTsLineEntry Definition: A list of terminal server line entries. Access: read-only. Status: optional. OBJECT: ltsLineEntry { ltsLineTable 1 } Syntax: LTsLineEntry ::= SEQUENCE { tsLineActive cisco MIB [Page 48] Request for Comments: Draft cisco Systems, Inc. INTEGER, tsLineType INTEGER, tsLineAutobaud INTEGER, tsLineSpeedin INTEGER, tsLineSpeedout INTEGER, tsLineFlow INTEGER, tsLineModem INTEGER, tsLineLoc OCTET STRING, tsLineTerm OCTET STRING, tsLineScrlen INTEGER, tsLineScrwid INTEGER, tsLineEsc OCTET STRING, tsLineTmo INTEGER, tsLineSestmo INTEGER, tsLineRotary INTEGER, tsLineUses INTEGER, tsLineNses INTEGER, tsLineUser OCTET STRING, } Definition: A collection of per TTY objects in the cisco Terminal Server implementation. Access: read-only. Status: cisco MIB [Page 49] Request for Comments: Draft cisco Systems, Inc. optional. The following section describes the components of the table. OBJECT: ------- tsLineActive { ltsLineEntry 1 } Syntax: INTEGER Definition: Boolean whether this line is active or not. Access: read-only. Status: optional. OBJECT: ------- tsLineType { ltsLineEntry 2 } Syntax: INTEGER { unknown(1), console(2), terminal(3), line-printer(4), virtual-terminal(5), auxiliary(6) } Definition: Type of line. Access: read-only. Status: optional. cisco MIB [Page 50] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- tsLineAutobaud { ltsLineEntry 3 } Syntax: INTEGER Definition: Boolean whether line will autobaud or not. Access: read-only. Status: optional. OBJECT: ------- tsLineSpeedin { ltsLineEntry 4 } Syntax: INTEGER Definition: What input speed the line is running at. Access: read-only. Status: optional. OBJECT: ------- tsLineSpeedout { ltsLineEntry 5 } Syntax: INTEGER Definition: What output speed the line is running at. Access: cisco MIB [Page 51] Request for Comments: Draft cisco Systems, Inc. read-only. Status: optional. OBJECT: ------- tsLineFlow { ltsLineEntry 6 } Syntax: INTEGER { unknown(1), none(2), software-input(3), software-output(4), software-both(5), hardware-input(6), hardware-output(7), hardware-both(8) } Definition: What kind of flow control the line is using. Access: read-only. Status: optional. OBJECT: ------- tsLineModem { ltsLineEntry 7 } Syntax: INTEGER { unknown(1), none(2), call-in(3), call-out(4), cts-required(5), rs-is-cd(6) } cisco MIB [Page 52] Request for Comments: Draft cisco Systems, Inc. Definition: What kind of modem control the line is using. Access: read-only. Status: optional. OBJECT: ------- tsLineLoc { ltsLineEntry 8 } Syntax: OCTET STRING Definition: Printable ascii string which describes the line's physical location. Access: read-only. Status: optional. OBJECT: ------- tsLineTerm { ltsLineEntry 9 } Syntax: OCTET STRING Definition: Printable ascii string which describes the line's terminal type. Access: read-only. Status: optional. cisco MIB [Page 53] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- tsLineScrlen { ltsLineEntry 10 } Syntax: INTEGER Definition: Length in lines of the screen of terminal attached to this line. Access: read-only. Status: optional. OBJECT: ------- tsLineScrwid { ltsLineEntry 11 } Syntax: INTEGER Definition: Width in characters of the screen of terminal attached to this line. Access: read-only. Status: optional. OBJECT: ------- tsLineEsc { ltsLineEntry 12 } Syntax: OCTET STRING Definition: Escape character used to break out of active cisco MIB [Page 54] Request for Comments: Draft cisco Systems, Inc. sessions. Access: read-only. Status: optional. OBJECT: ------- tsLineTmo { ltsLineEntry 13 } Syntax: INTEGER Definition: Line idleness timeout in seconds. Access: read-only. Status: optional. OBJECT: ------- tsLineSestmo { ltsLineEntry 14 } Syntax: INTEGER Definition: Session idleness timeout in second. Access: read-only. Status: optional. OBJECT: ------- cisco MIB [Page 55] Request for Comments: Draft cisco Systems, Inc. tsLineRotary { ltsLineEntry 15 } Syntax: INTEGER Definition: Rotary group number the line belongs in. Access: read-only. Status: optional. OBJECT: ------- tsLineUses { ltsLineEntry 16 } Syntax: INTEGER Definition: Number of times this line was been activated. Access: read-only. Status: optional. OBJECT: ------- tsLineNses { ltsLineEntry 17 } Syntax: INTEGER Definition: Current number of sessions in use on this line. Access: read-only. cisco MIB [Page 56] Request for Comments: Draft cisco Systems, Inc. Status: optional. OBJECT: ------- tsLineUser { ltsLineEntry 18 } Syntax: OCTET STRING Definition: TACACS user name, if TACACS enabled, of user on this line. Access: read-only. Status: optional. 3.2.5.2. Local Terminal Server Line Session Table This group contains terminal server specific information on a per line and session basis. OBJECT: ------- ltsLineSessionTable { lts 3 } Syntax: SEQUENCE OF LTsLineSessionEntry Definition: A list of terminal server line and session entries. Access: read-only. Status: optional. OBJECT: cisco MIB [Page 57] Request for Comments: Draft cisco Systems, Inc. ltsLineSessionEntry { ltsLineSessionTable 1 } Syntax: LTsLineSessionEntry ::= SEQUENCE { tslineSesType INTEGER, tslineSesDir INTEGER, tslineSesAddr NetworkAddress, tslineSesName OCTET STRING, tslineSesCur INTEGER, tslineSesIdle INTEGER, } Definition: A collection of per session and per TTY objects in the cisco Terminal Server implementation. Access: read-only. Status: optional. The following section describes the components of the table. OBJECT: ------- tslineSesType { ltsLineSessionEntry 1 } Syntax: INTEGER { unknown(1), pad(2), stream(3), rlogin(4), telnet(5) } Definition: cisco MIB [Page 58] Request for Comments: Draft cisco Systems, Inc. Type of session. Access: read-only. Status: optional. OBJECT: ------- tslineSesDir { ltsLineSessionEntry 2 } Syntax: INTEGER { unknown(1), incoming(2), outgoing(3) } Definition: Direction of session. Access: read-only. Status: optional. OBJECT: ------- tslineSesAddr { ltsLineSessionEntry 3 } Syntax: NetworkAddress Definition: Remote host address of session. [What about PAD connections?] Access: read-only. Status: cisco MIB [Page 59] Request for Comments: Draft cisco Systems, Inc. optional. OBJECT: ------- tslineSesName { ltsLineSessionEntry 4 } Syntax: OCTET STRING Definition: Remote host name of session. Access: read-only. Status: optional. OBJECT: ------- tslineSesCur { ltsLineSessionEntry 5 } Syntax: INTEGER Definition: Boolean whether session is the currently active one. Access: read-only. Status: optional. OBJECT: ------- tslineSesIdle { ltsLineSessionEntry 6 } Syntax: INTEGER Definition: cisco MIB [Page 60] Request for Comments: Draft cisco Systems, Inc. Time in seconds session has been idle. Access: read-only. Status: optional. 3.3. Temporary Variable Section This section is equivalent to the experimental space defined by the SMI. It contains variables that are useful to have but are beyond cisco's ability to control and maintain. This section can change from release to release without warning. This document controls what is contained here for this version. 3.3.1. Temporary DECNET Section This group is present in all router based products. OBJECT: ------- dnForward { decnet 1 } Syntax: INTEGER Definition: Total count of DECNET packets forwarded. Access: read-only. Status: experimental. OBJECT: ------- dnReceived { decnet 2 } Syntax: INTEGER cisco MIB [Page 61] Request for Comments: Draft cisco Systems, Inc. Definition: Count of total DECNET packets received. Access: read-only. Status: experimental. OBJECT: ------- dnFormaterr { decnet 3 } Syntax: INTEGER Definition: Total number of DECNET packets received with header errors. Access: read-only. Status: experimental. OBJECT: ------- dnNotgateway { decnet 4 } Syntax: INTEGER Definition: Total number of packets received while not routing. Access: read-only. Status: experimental. cisco MIB [Page 62] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- dnNotimp { decnet 5 } Syntax: INTEGER Definition: Total number of received unknown control packets. Access: read-only. Status: experimental. OBJECT: ------- dnHellos { decnet 6 } Syntax: INTEGER Definition: Total number of Hellos received. Access: read-only. Status: experimental. OBJECT: ------- dnBadhello { decnet 7 } Syntax: INTEGER Definition: Total number of received bad Hellos. Access: cisco MIB [Page 63] Request for Comments: Draft cisco Systems, Inc. read-only. Status: experimental. OBJECT: ------- dnNotlong { decnet 8 } Syntax: INTEGER Definition: Total number of received packets not in long format. Access: read-only. Status: experimental. OBJECT: ------- dnDatas { decnet 9 } Syntax: INTEGER Definition: Total number of received data packets. Access: read-only. Status: experimental. OBJECT: ------- dnBigaddr { decnet 10 } Syntax: cisco MIB [Page 64] Request for Comments: Draft cisco Systems, Inc. INTEGER Definition: Total number of too large addresses. Access: read-only. Status: experimental. OBJECT: ------- dnNoroute { decnet 11 } Syntax: INTEGER Definition: Total number of packets dropped due to no route present. Access: read-only. Status: experimental. OBJECT: ------- dnNoencap { decnet 12 } Syntax: INTEGER Definition: Total number of packets dropped due to output encapsulation failure. Access: read-only. Status: cisco MIB [Page 65] Request for Comments: Draft cisco Systems, Inc. experimental. OBJECT: ------- dnLevel1s { decnet 13 } Syntax: INTEGER Definition: Total number of Level 1 routing packets received. Access: read-only. Status: experimental. OBJECT: ------- dnBadlevel1 { decnet 14 } Syntax: INTEGER Definition: Total number of bad Level 1 routing packets received. Access: read-only. Status: experimental. OBJECT: ------- dnToomanyhops { decnet 15 } Syntax: INTEGER cisco MIB [Page 66] Request for Comments: Draft cisco Systems, Inc. Definition: Total number of packets received which cisited too many nodes. Access: read-only. Status: experimental. OBJECT: ------- dnHellosent { decnet 16 } Syntax: INTEGER Definition: Total numver of Hellos output. Access: read-only. Status: experimental. OBJECT: ------- dnLevel1sent { decnet 17 } Syntax: INTEGER Definition: Total number of Level 1 routing packets sent. Access: read-only. Status: experimental. cisco MIB [Page 67] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- dnNomemory { decnet 18 } Syntax: INTEGER Definition: Total number of memory requests denied. Access: read-only. Status: experimental. OBJECT: ------- dnOtherhello { decnet 19 } Syntax: INTEGER Definition: Total number of Hellos received from another area. Access: read-only. Status: experimental. OBJECT: ------- dnOtherlevel1 { decnet 20 } Syntax: INTEGER Definition: Total number of Level 1 routing packets received from another area. cisco MIB [Page 68] Request for Comments: Draft cisco Systems, Inc. Access: read-only. Status: experimental. OBJECT: ------- dnLevel2s { decnet 21 } Syntax: INTEGER Definition: Total number of Level 2 routing packets received. Access: read-only. Status: experimental. OBJECT: ------- dnLevel2sent { decnet 22 } Syntax: INTEGER Definition: Total number of Level 2 routing packets sent. Access: read-only. Status: experimental. OBJECT: ------- dnNovector { decnet 23 } cisco MIB [Page 69] Request for Comments: Draft cisco Systems, Inc. Syntax: INTEGER Definition: Total number of missing routing vectors. Access: read-only. Status: experimental. OBJECT: ------- dnOtherlevel2 { decnet 24 } Syntax: INTEGER Definition: Total number of received Level 2 routing packets from another area. Access: read-only. Status: experimental. OBJECT: ------- dnNoaccess { decnet 25 } Syntax: INTEGER Definition: Total number of packets dropped due to access control failure. Access: read-only. cisco MIB [Page 70] Request for Comments: Draft cisco Systems, Inc. Status: experimental. 3.3.2. Temporary XNS Section This group is present in all router based products. OBJECT: ------- xnsInput { xns 1 } Syntax: INTEGER Definition: Total input count of number of XNS packets. Access: read-only. Status: experimental. OBJECT: ------- xnsLocal { xns 2 } Syntax: INTEGER Definition: Total count of XNS input packets for this host. Access: read-only. Status: experimental. OBJECT: ------- xnsBcastin { xns 3 } cisco MIB [Page 71] Request for Comments: Draft cisco Systems, Inc. Syntax: INTEGER Definition: Total count of number of XNS input broadcast packets. Access: read-only. Status: experimental. OBJECT: ------- xnsForward { xns 4 } Syntax: INTEGER Definition: Total count of number of XNS packets forwarded. Access: read-only. Status: experimental. OBJECT: ------- xnsBcastout { xns 5 } Syntax: INTEGER Definition: Total count of number of XNS output broadcast packets. Access: read-only. cisco MIB [Page 72] Request for Comments: Draft cisco Systems, Inc. Status: experimental. OBJECT: ------- xnsErrin { xns 6 } Syntax: INTEGER Definition: Total count of number of XNS Error input packets. Access: read-only. Status: experimental. OBJECT: ------- xnsErrout { xns 7 } Syntax: INTEGER Definition: Total count of number of XNS Error output packets. Access: read-only. Status: experimental. OBJECT: ------- xnsFormerr { xns 8 } Syntax: INTEGER cisco MIB [Page 73] Request for Comments: Draft cisco Systems, Inc. Definition: Total count of number of XNS input packets with header errors. Access: read-only. Status: experimental. OBJECT: ------- xnsChksum { xns 9 } Syntax: INTEGER Definition: Total count of number of XNS input packets with checksum erors. Access: read-only. Status: experimental. OBJECT: ------- xnsNotgate { xns 10 } Syntax: INTEGER Definition: Total count of number of XNS input packets received while not routing. Access: read-only. Status: experimental. cisco MIB [Page 74] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- xnsHopcnt { xns 11 } Syntax: INTEGER Definition: Total count of number of XNS input packets that have exceeded the maximum hop count. Access: read-only. Status: experimental. OBJECT: ------- xnsNoroute { xns 12 } Syntax: INTEGER Definition: Total count of number of XNS packets dropped due to no route. Access: read-only. Status: experimental. OBJECT: ------- xnsNoencap { xns 13 } Syntax: INTEGER Definition: Total count of number of XNS packets dropped due to cisco MIB [Page 75] Request for Comments: Draft cisco Systems, Inc. output encapsulation failed. Access: read-only. Status: experimental. OBJECT: ------- xnsOutput { xns 14 } Syntax: INTEGER Definition: Total count of number of XNS output packets. Access: read-only. Status: experimental. OBJECT: ------- xnsInmult { xns 15 } Syntax: INTEGER Definition: Total count of number of XNS input multicast packets. Access: read-only. Status: experimental. OBJECT: cisco MIB [Page 76] Request for Comments: Draft cisco Systems, Inc. ------- xnsUnknown { xns 16 } Syntax: INTEGER Definition: Total count of number of unknown XNS input packets. Access: read-only. Status: experimental. OBJECT: ------- xnsFwdbrd { xns 17 } Syntax: INTEGER Definition: Total count of number of XNS broadcast packets forwarded. Access: read-only. Status: experimental. OBJECT: ------- xnsEchoreqin { xns 18 } Syntax: INTEGER Definition: Total count of number of XNS Echo request packets received. cisco MIB [Page 77] Request for Comments: Draft cisco Systems, Inc. Access: read-only. Status: experimental. OBJECT: ------- xnsEchoreqout { xns 19 } Syntax: INTEGER Definition: Total count of number of XNS Echo request packets sent. Access: read-only. Status: experimental. OBJECT: ------- xnsEchorepin { xns 20 } Syntax: INTEGER Definition: Total count of number of XNS Echo reply packets received. Access: read-only. Status: experimental. OBJECT: ------- cisco MIB [Page 78] Request for Comments: Draft cisco Systems, Inc. xnsEchorepout { xns 21 } Syntax: INTEGER Definition: Total count of number of XNS Echo reply packets sent. Access: read-only. Status: experimental. 3.3.3. Temporary AppleTalk Section This group is present in all router based products. OBJECT: ------- atInput { appletalk 1 } Syntax: INTEGER Definition: Total input count of number of AppleTalk packets. Access: read-only. Status: experimental. OBJECT: ------- atLocal { appletalk 2 } Syntax: INTEGER Definition: cisco MIB [Page 79] Request for Comments: Draft cisco Systems, Inc. Total count of AppleTalk input packets for this host. Access: read-only. Status: experimental. OBJECT: ------- atBcastin { appletalk 3 } Syntax: INTEGER Definition: Total count of number of AppleTalk input broadcast packets. Access: read-only. Status: experimental. OBJECT: ------- atForward { appletalk 4 } Syntax: INTEGER Definition: Total count of number of AppleTalk packets forwarded. Access: read-only. Status: experimental. cisco MIB [Page 80] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- atBcastout { appletalk 5 } Syntax: INTEGER Definition: Total count of number of AppleTalk output broadcast packets. Access: read-only. Status: experimental. OBJECT: ------- atFormerr { appletalk 6 } Syntax: INTEGER Definition: Total count of number of AppleTalk input packets with header errors. Access: read-only. Status: experimental. OBJECT: ------- atChksum { appletalk 7 } Syntax: INTEGER Definition: Total count of number of AppleTalk input packets cisco MIB [Page 81] Request for Comments: Draft cisco Systems, Inc. with checksum erors. Access: read-only. Status: experimental. OBJECT: ------- atNotgate { appletalk 8 } Syntax: INTEGER Definition: Total count of AppleTalk input packets received while not routing. Access: read-only. Status: experimental. OBJECT: ------- atHopcnt { appletalk 9 } Syntax: INTEGER Definition: Total count of number of AppleTalk input packets that have exceeded the maximum hop count. Access: read-only. Status: experimental. cisco MIB [Page 82] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- atNoaccess { appletalk 10 } Syntax: INTEGER Definition: Total number of AppleTalk packets dropped due to access control. Access: read-only. Status: experimental. OBJECT: ------- atNoroute { appletalk 11 } Syntax: INTEGER Definition: Total count of number of AppleTalk packets dropped due to no route. Access: read-only. Status: experimental. OBJECT: ------- atNoencap { appletalk 12 } Syntax: INTEGER Definition: Total count of number of AppleTalk packets dropped cisco MIB [Page 83] Request for Comments: Draft cisco Systems, Inc. due to output encapsulation failed. Access: read-only. Status: experimental. OBJECT: ------- atOutput { appletalk 13 } Syntax: INTEGER Definition: Total count of number of AppleTalk output packets. Access: read-only. Status: experimental. OBJECT: ------- atInmult { appletalk 14 } Syntax: INTEGER Definition: Total count of number of AppleTalk input multicast packets. Access: read-only. Status: experimental. OBJECT: cisco MIB [Page 84] Request for Comments: Draft cisco Systems, Inc. ------- atRtmpin { appletalk 15 } Syntax: INTEGER Definition: Total count of number of AppleTalk RTMP packets received. Access: read-only. Status: experimental. OBJECT: ------- atRtmpout { appletalk 16 } Syntax: INTEGER Definition: Total count of number of AppleTalk RTMP packets sent. Access: read-only. Status: experimental. OBJECT: ------- atNbpin { appletalk 17 } Syntax: INTEGER Definition: Total count of number of AppleTalk NBP packets received. cisco MIB [Page 85] Request for Comments: Draft cisco Systems, Inc. Access: read-only. Status: experimental. OBJECT: ------- atNbpout { appletalk 18 } Syntax: INTEGER Definition: Total count of number of AppleTalk NBP packets sent. Access: read-only. Status: experimental. OBJECT: ------- atAtp { appletalk 19 } Syntax: INTEGER Definition: Total count of number of AppleTalk ATP packets received. Access: read-only. Status: experimental. OBJECT: ------- atZipin { appletalk 20 } cisco MIB [Page 86] Request for Comments: Draft cisco Systems, Inc. Syntax: INTEGER Definition: Total count of number of AppleTalk ZIP packets received. Access: read-only. Status: experimental. OBJECT: ------- atZipout { appletalk 21 } Syntax: INTEGER Definition: Total count of number of AppleTalk ZIP packets sent. Access: read-only. Status: experimental. OBJECT: ------- atEcho { appletalk 22 } Syntax: INTEGER Definition: Total count of number of AppleTalk Echo packets received. Access: read-only. cisco MIB [Page 87] Request for Comments: Draft cisco Systems, Inc. Status: experimental. OBJECT: ------- atEchoill { appletalk 23 } Syntax: INTEGER Definition: Total count of number of illegal AppleTalk Echo packets received. Access: read-only. Status: experimental. OBJECT: ------- atDdpshort { appletalk 24 } Syntax: INTEGER Definition: Total count of number of short AppleTalk DDP packets received. Access: read-only. Status: experimental. OBJECT: ------- atDdplong { appletalk 25 } Syntax: cisco MIB [Page 88] Request for Comments: Draft cisco Systems, Inc. INTEGER Definition: Total count of number of long AppleTalk DDP packets received. Access: read-only. Status: experimental. OBJECT: ------- atDdpbad { appletalk 26 } Syntax: INTEGER Definition: Total count of number of illegal sized AppleTalk DDP packets received. Access: read-only. Status: experimental. OBJECT: ------- atNobuffer { appletalk 27 } Syntax: INTEGER Definition: Total count of number of AppleTalk packets lost due to no memory. Access: read-only. cisco MIB [Page 89] Request for Comments: Draft cisco Systems, Inc. Status: experimental. OBJECT: ------- atArpreq { appletalk 28 } Syntax: INTEGER Definition: Total count of number of input AppleTalk ARP request packets. Access: read-only. Status: experimental. OBJECT: ------- atArpreply { appletalk 29 } Syntax: INTEGER Definition: Total count of number of AppleTalk ARP reply packets output. Access: read-only. Status: experimental. OBJECT: ------- atArpprobe { appletalk 30 } Syntax: cisco MIB [Page 90] Request for Comments: Draft cisco Systems, Inc. INTEGER Definition: Total count of number of input AppleTalk ARP probe packets. Access: read-only. Status: experimental. OBJECT: ------- atUnknown { appletalk 31 } Syntax: INTEGER Definition: Total count of number of unknown AppleTalk input packets. Access: read-only. Status: experimental. 3.3.4. Temporary Novell Section This group is present in all router based products. OBJECT: ------- novellInput { novell 1 } Syntax: INTEGER Definition: Total input count of number of NOVELL packets. cisco MIB [Page 91] Request for Comments: Draft cisco Systems, Inc. Access: read-only. Status: experimental. OBJECT: ------- novellBcastin { novell 2 } Syntax: INTEGER Definition: Total count of number of NOVELL input broadcast packets. Access: read-only. Status: experimental. OBJECT: ------- novellForward { novell 3 } Syntax: INTEGER Definition: Total count of number of NOVELL packets forwarded. Access: read-only. Status: experimental. OBJECT: ------- novellBcastout { novell 4 } cisco MIB [Page 92] Request for Comments: Draft cisco Systems, Inc. Syntax: INTEGER Definition: Total count of number of NOVELL output broadcast packets. Access: read-only. Status: experimental. OBJECT: ------- novellFormerr { novell 5 } Syntax: INTEGER Definition: Total count of number of NOVELL input packets with header errors. Access: read-only. Status: experimental. OBJECT: ------- novellChksum { novell 6 } Syntax: INTEGER Definition: Total count of number of NOVELL input packets with checksum erors. Access: read-only. cisco MIB [Page 93] Request for Comments: Draft cisco Systems, Inc. Status: experimental. OBJECT: ------- novellHopcnt { novell 7 } Syntax: INTEGER Definition: Total count of number of NOVELL input packets that have exceeded the maximum hop count. Access: read-only. Status: experimental. OBJECT: ------- novellNoroute { novell 8 } Syntax: INTEGER Definition: Total count of number of NOVELL packets dropped due to no route. Access: read-only. Status: experimental. OBJECT: ------- novellNoencap { novell 9 } Syntax: cisco MIB [Page 94] Request for Comments: Draft cisco Systems, Inc. INTEGER Definition: Total count of number of NOVELL packets dropped due to output encapsulation failed. Access: read-only. Status: experimental. OBJECT: ------- novellOutput { novell 10 } Syntax: INTEGER Definition: Total count of number of NOVELL output packets. Access: read-only. Status: experimental. OBJECT: ------- novellInmult { novell 11 } Syntax: INTEGER Definition: Total count of number of NOVELL input multicast packets. Access: read-only. Status: cisco MIB [Page 95] Request for Comments: Draft cisco Systems, Inc. experimental. OBJECT: ------- novellLocal { novell 12 } Syntax: INTEGER Definition: Total count of NOVELL input packets for this host. Access: read-only. Status: experimental. OBJECT: ------- novellUnknown { novell 13 } Syntax: INTEGER Definition: Total count of number of unknown NOVELL input packets. Access: read-only. Status: experimental. OBJECT: ------- novellSapreqin { novell 14 } Syntax: INTEGER cisco MIB [Page 96] Request for Comments: Draft cisco Systems, Inc. Definition: Total count of number of NOVELL SAP request packets received. Access: read-only. Status: experimental. OBJECT: ------- novellSapresin { novell 15 } Syntax: INTEGER Definition: Total count of number of NOVELL SAP response packets received. Access: read-only. Status: experimental. OBJECT: ------- novellSapout { novell 16 } Syntax: INTEGER Definition: Total count of number of NOVELL SAP request packets sent. Access: read-only. Status: experimental. cisco MIB [Page 97] Request for Comments: Draft cisco Systems, Inc. OBJECT: ------- novellSapreply { novell 17 } Syntax: INTEGER Definition: Total count of number of NOVELL SAP reply packets sent. Access: read-only. Status: experimental. 4. Definitions CISCO-MIB { iso org(3) dod(6) internet(1) private(4) enterprises(1) 9 } DEFINITIONS ::= BEGIN IMPORTS enterprises, OBJECT-TYPE, NetworkAddress, IpAddress, Counter, Gauge, TimeTicks, OBJECT-TYPE FROM RFC1065-SMI cisco OBJECT IDENTIFIER ::= { enterprises 9 } products OBJECT IDENTIFIER ::= { cisco 1 } local OBJECT IDENTIFIER ::= { cisco 2 } temporary OBJECT IDENTIFIER ::= { cisco 3 } gateway-server OBJECT IDENTIFIER ::= { products 1 } terminal-server OBJECT IDENTIFIER ::= { products 2 } trouter OBJECT IDENTIFIER ::= { products 3 } protocol-translator OBJECT IDENTIFIER ::= { products 4 } lsystem OBJECT IDENTIFIER ::= { local 1 } linterfaces OBJECT IDENTIFIER ::= { local 2 } lat OBJECT IDENTIFIER ::= { local 3 } cisco MIB [Page 98] Request for Comments: Draft cisco Systems, Inc. lip OBJECT IDENTIFIER ::= { local 4 } licmp OBJECT IDENTIFIER ::= { local 5 } ltcp OBJECT IDENTIFIER ::= { local 6 } ludp OBJECT IDENTIFIER ::= { local 7 } legp OBJECT IDENTIFIER ::= { local 8 } lts OBJECT IDENTIFIER ::= { local 9 } decnet OBJECT IDENTIFIER ::= { temporary 1 } xns OBJECT IDENTIFIER ::= { temporary 2 } appletalk OBJECT IDENTIFIER ::= { temporary 3 } novell OBJECT IDENTIFIER ::= { temporary 4 } -- the Local System group romId OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { lsystem 1 } whyReload OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { lsystem 2 } hostName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { lsystem 3 } domainName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { lsystem 4 } authAddr OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-only STATUS mandatory ::= { lsystem 5 } bootHost OBJECT-TYPE cisco MIB [Page 99] Request for Comments: Draft cisco Systems, Inc. SYNTAX NetworkAddress ACCESS read-only STATUS mandatory ::= { lsystem 6 } ping OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory ::= { lsystem 7 } freeMem OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 8 } bufferElFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 9 } bufferElMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 10 } bufferElHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 11 } bufferElMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 12 } bufferElCreate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory cisco MIB [Page 100] Request for Comments: Draft cisco Systems, Inc. ::= { lsystem 13 } bufferSmSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 14 } bufferSmTotal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 15 } bufferSmFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 16 } bufferSmMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 17 } bufferSmHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 18 } bufferSmMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 19 } bufferSmTrim OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 20 } bufferSmCreate OBJECT-TYPE cisco MIB [Page 101] Request for Comments: Draft cisco Systems, Inc. SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 21 } bufferMdSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 22 } bufferMdTotal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 23 } bufferMdFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 24 } bufferMdMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 25 } bufferMdHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 26 } bufferMdMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 27 } bufferMdTrim OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory cisco MIB [Page 102] Request for Comments: Draft cisco Systems, Inc. ::= { lsystem 28 } bufferMdCreate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 29 } bufferBgSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 30 } bufferBgTotal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 31 } bufferBgFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 32 } bufferBgMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 33 } bufferBgHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 34 } bufferBgMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 35 } bufferBgTrim OBJECT-TYPE cisco MIB [Page 103] Request for Comments: Draft cisco Systems, Inc. SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 36 } bufferBgCreate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 37 } bufferLgSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 38 } bufferLgTotal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 39 } bufferLgFree OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 40 } bufferLgMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 41 } bufferLgHit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 42 } bufferLgMiss OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory cisco MIB [Page 104] Request for Comments: Draft cisco Systems, Inc. ::= { lsystem 43 } bufferLgTrim OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 44 } bufferLgCreate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 45 } bufferFail OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 46 } bufferNoMem OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lsystem 47 } netConfigIP OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-only STATUS mandatory ::= { lsystem 48 } netConfigName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { lsystem 49 } netConfigSet OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory ::= { lsystem 50 } hostConfigIP OBJECT-TYPE cisco MIB [Page 105] Request for Comments: Draft cisco Systems, Inc. SYNTAX NetworkAddress ACCESS read-only STATUS mandatory ::= { lsystem 51 } hostConfigName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { lsystem 52 } hostConfigSet OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory ::= { lsystem 53 } -- the Local Interfaces group -- the Local Interface Table lifTable OBJECT-TYPE SYNTAX SEQUENCE OF LIfEntry ACCESS read-only STATUS mandatory ::= { linterfaces 1 } lifEntry OBJECT-TYPE SYNTAX LIfEntry ACCESS read-only STATUS mandatory ::= { lifTable 1 } LIfEntry ::= SEQUENCE { locIfHardType OCTET STRING, locIfLineProt INTEGER, locIfLastIn INTEGER, locIfLastOut INTEGER, locIfLastOutHang INTEGER, locIfInBitsSec INTEGER, cisco MIB [Page 106] Request for Comments: Draft cisco Systems, Inc. locIfInPktsSec INTEGER, locIfOutBitsSec INTEGER, locIfOutPktsSec INTEGER, locIfInRunts INTEGER, locIfInGiants INTEGER, locIfInCRC INTEGER, locIfInFrame INTEGER, locIfInOverrun INTEGER, locIfInIgnored INTEGER, locIfInAbort INTEGER, locIfResets INTEGER, locIfRestarts INTEGER, locIfKeep INTEGER, locIfReason OCTET STRING, } locIfHardType OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { lifEntry 1 } locIfLineProt OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 2 } locIfLastIn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only cisco MIB [Page 107] Request for Comments: Draft cisco Systems, Inc. STATUS mandatory ::= { lifEntry 3 } locIfLastOut OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 4 } locIfLastOutHang OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 5 } locIfInBitsSec OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 6 } locIfInPktsSec OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 7 } locIfOutBitsSec OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 8 } locIfOutPktsSec OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 9 } locIfInRunts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 10 } cisco MIB [Page 108] Request for Comments: Draft cisco Systems, Inc. locIfInGiants OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 11 } locIfInCRC OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 12 } locIfInFrame OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 13 } locIfInOverrun OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 14 } locIfInIgnored OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 15 } locIfInAbort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 16 } locIfResets OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 17 } locIfRestarts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only cisco MIB [Page 109] Request for Comments: Draft cisco Systems, Inc. STATUS mandatory ::= { lifEntry 18 } locIfKeep OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lifEntry 19 } locIfReason OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { lifEntry 20 } -- the Local IP group -- the Local IP Address table lipAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF LIpAddrEntry ACCESS read-only STATUS mandatory ::= { lip 1 } lipAddrEntry OBJECT-TYPE SYNTAX LIpAddrEntry ACCESS read-only STATUS mandatory ::= { lipAddrTable 1 } LIpAddrEntry ::= SEQUENCE { locIPHow OCTET STRING, locIPWho NetworkAddress, locIPHelper NetworkAddress, locIPSecurity INTEGER, locIPRedirects INTEGER, locIPUnreach INTEGER, } cisco MIB [Page 110] Request for Comments: Draft cisco Systems, Inc. locIPHow OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory ::= { lipAddrEntry 1 } locIPWho OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-only STATUS mandatory ::= { lipAddrEntry 2 } locIPHelper OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-only STATUS mandatory ::= { lipAddrEntry 3 } locIPSecurity OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lipAddrEntry 4 } locIPRedirects OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lipAddrEntry 5 } locIPUnreach OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lipAddrEntry 6 } -- theLocal IP Routing table lipRoutingTable OBJECT-TYPE SYNTAX SEQUENCE OF LIpRouteEntry ACCESS read-only STATUS mandatory ::= { lip 2 } lipRouteEntry OBJECT-TYPE cisco MIB [Page 111] Request for Comments: Draft cisco Systems, Inc. SYNTAX LIpRouteEntry ACCESS read-only STATUS mandatory ::= { lipRoutingTable 1 } LIpRouteEntry ::= SEQUENCE { locRtMask NetworkAddress, locRtCount INTEGER, locRtUses INTEGER, } locRtMask OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-only STATUS mandatory ::= { lipRouteEntry 1 } locRtCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lipRouteEntry 2 } locRtUses OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lipRouteEntry 3 } routeFilter OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lip 3 } actThresh OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lip 4 } actLostPkts OBJECT-TYPE cisco MIB [Page 112] Request for Comments: Draft cisco Systems, Inc. SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lip 5 } actLostByts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lip 6 } -- the Local IP Accounting table lipAccountingTable OBJECT-TYPE SYNTAX SEQUENCE OF LIpAccountEntry ACCESS read-only STATUS mandatory ::= { lip 7 } lipAccountEntry OBJECT-TYPE SYNTAX LIpAccountEntry ACCESS read-only STATUS mandatory ::= { lipAccountingTable 1 } LIpAccountEntry ::= SEQUENCE { actSrc NetworkAddress, actDst NetworkAddress, actPkts INTEGER, actByts INTEGER, } actSrc OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-only STATUS mandatory ::= { lipAccountEntry 1 } actDst OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-only cisco MIB [Page 113] Request for Comments: Draft cisco Systems, Inc. STATUS mandatory ::= { lipAccountEntry 2 } actPkts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lipAccountEntry 3 } actByts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { lipAccountEntry 4 } -- the Local TCP group -- the Local TCP Connection table ltcpConnTable OBJECT-TYPE SYNTAX SEQUENCE OF LTcpConnEntry ACCESS read-only STATUS mandatory ::= { ltcp 1 } ltcpConnEntry OBJECT-TYPE SYNTAX LTcpConnEntry ACCESS read-only STATUS mandatory ::= { ltcpConnTable 1 } LTcpConnEntry ::= SEQUENCE { loctcpConnInBytes INTEGER, loctcpConnOutBytes INTEGER, loctcpConnInPkts INTEGER, loctcpConnOutPkts INTEGER, loctcpConnElapsed TimeTicks, } loctcpConnInBytes OBJECT-TYPE SYNTAX INTEGER cisco MIB [Page 114] Request for Comments: Draft cisco Systems, Inc. ACCESS read-only STATUS mandatory ::= { ltcpConnEntry 1 } loctcpConnOutBytes OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { ltcpConnEntry 2 } loctcpConnInPkts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { ltcpConnEntry 3 } loctcpConnOutPkts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory ::= { ltcpConnEntry 4 } loctcpConnElapsed OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory ::= { ltcpConnEntry 5 } -- the Local Terminal Server group tsLines OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { lts 1 } -- the Local Terminal Server Line table ltsLineTable OBJECT-TYPE SYNTAX SEQUENCE OF LTsLineEntry ACCESS read-only STATUS optional ::= { lts 2 } ltsLineEntry OBJECT-TYPE SYNTAX LTsLineEntry cisco MIB [Page 115] Request for Comments: Draft cisco Systems, Inc. ACCESS read-only STATUS optional ::= { ltsLineTable 1 } LTsLineEntry ::= SEQUENCE { tsLineActive INTEGER, tsLineType INTEGER, tsLineAutobaud INTEGER, tsLineSpeedin INTEGER, tsLineSpeedout INTEGER, tsLineFlow INTEGER, tsLineModem INTEGER, tsLineLoc OCTET STRING, tsLineTerm OCTET STRING, tsLineScrlen INTEGER, tsLineScrwid INTEGER, tsLineEsc OCTET STRING, tsLineTmo INTEGER, tsLineSestmo INTEGER, tsLineRotary INTEGER, tsLineUses INTEGER, tsLineNses INTEGER, tsLineUser OCTET STRING, } tsLineActive OBJECT-TYPE SYNTAX INTEGER cisco MIB [Page 116] Request for Comments: Draft cisco Systems, Inc. ACCESS read-only STATUS optional ::= { ltsLineEntry 1 } tsLineType OBJECT-TYPE SYNTAX INTEGER { unknown(1), console(2), terminal(3), line-printer(4), virtual-terminal(5), auxiliary(6) } ACCESS read-only STATUS optional ::= { ltsLineEntry 2 } tsLineAutobaud OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineEntry 3 } tsLineSpeedin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineEntry 4 } tsLineSpeedout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineEntry 5 } tsLineFlow OBJECT-TYPE SYNTAX INTEGER { unknown(1), none(2), software-input(3), software-output(4), software-both(5), hardware-input(6), hardware-output(7), hardware-both(8) cisco MIB [Page 117] Request for Comments: Draft cisco Systems, Inc. } ACCESS read-only STATUS optional ::= { ltsLineEntry 6 } tsLineModem OBJECT-TYPE SYNTAX INTEGER { unknown(1), none(2), call-in(3), call-out(4), cts-required(5), rs-is-cd(6) } ACCESS read-only STATUS optional ::= { ltsLineEntry 7 } tsLineLoc OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional ::= { ltsLineEntry 8 } tsLineTerm OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional ::= { ltsLineEntry 9 } tsLineScrlen OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineEntry 10 } tsLineScrwid OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineEntry 11 } tsLineEsc OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only cisco MIB [Page 118] Request for Comments: Draft cisco Systems, Inc. STATUS optional ::= { ltsLineEntry 12 } tsLineTmo OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineEntry 13 } tsLineSestmo OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineEntry 14 } tsLineRotary OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineEntry 15 } tsLineUses OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineEntry 16 } tsLineNses OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineEntry 17 } tsLineUser OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional ::= { ltsLineEntry 18 } -- the Local Terminal Server Line Session table ltsLineSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF LTsLineSessionEntry ACCESS read-only STATUS optional cisco MIB [Page 119] Request for Comments: Draft cisco Systems, Inc. ::= { lts 3 } ltsLineSessionEntry OBJECT-TYPE SYNTAX LTsLineSessionEntry ACCESS read-only STATUS optional ::= { ltsLineSessionTable 1 } LTsLineSessionEntry ::= SEQUENCE { tslineSesType INTEGER, tslineSesDir INTEGER, tslineSesAddr NetworkAddress, tslineSesName OCTET STRING, tslineSesCur INTEGER, tslineSesIdle INTEGER, } tslineSesType OBJECT-TYPE SYNTAX INTEGER { unknown(1), pad(2), stream(3), rlogin(4), telnet(5) } ACCESS read-only STATUS optional ::= { ltsLineSessionEntry 1 } tslineSesDir OBJECT-TYPE SYNTAX INTEGER { unknown(1), incoming(2), outgoing(3) } ACCESS read-only STATUS optional ::= { ltsLineSessionEntry 2 } cisco MIB [Page 120] Request for Comments: Draft cisco Systems, Inc. tslineSesAddr OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-only STATUS optional ::= { ltsLineSessionEntry 3 } tslineSesName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS optional ::= { ltsLineSessionEntry 4 } tslineSesCur OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineSessionEntry 5 } tslineSesIdle OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS optional ::= { ltsLineSessionEntry 6 } -- the Temporary DECNET group dnForward OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 1 } dnReceived OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 2 } dnFormaterr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 3 } dnNotgateway OBJECT-TYPE SYNTAX INTEGER cisco MIB [Page 121] Request for Comments: Draft cisco Systems, Inc. ACCESS read-only STATUS experimental ::= { decnet 4 } dnNotimp OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 5 } dnHellos OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 6 } dnBadhello OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 7 } dnNotlong OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 8 } dnDatas OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 9 } dnBigaddr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 10 } dnNoroute OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 11 } cisco MIB [Page 122] Request for Comments: Draft cisco Systems, Inc. dnNoencap OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 12 } dnLevel1s OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 13 } dnBadlevel1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 14 } dnToomanyhops OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 15 } dnHellosent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 16 } dnLevel1sent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 17 } dnNomemory OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 18 } dnOtherhello OBJECT-TYPE SYNTAX INTEGER ACCESS read-only cisco MIB [Page 123] Request for Comments: Draft cisco Systems, Inc. STATUS experimental ::= { decnet 19 } dnOtherlevel1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 20 } dnLevel2s OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 21 } dnLevel2sent OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 22 } dnNovector OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 23 } dnOtherlevel2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 24 } dnNoaccess OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { decnet 25 } -- the Temporary XNS group xnsInput OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 1 } cisco MIB [Page 124] Request for Comments: Draft cisco Systems, Inc. xnsLocal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 2 } xnsBcastin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 3 } xnsForward OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 4 } xnsBcastout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 5 } xnsErrin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 6 } xnsErrout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 7 } xnsFormerr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 8 } xnsChksum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only cisco MIB [Page 125] Request for Comments: Draft cisco Systems, Inc. STATUS experimental ::= { xns 9 } xnsNotgate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 10 } xnsHopcnt OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 11 } xnsNoroute OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 12 } xnsNoencap OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 13 } xnsOutput OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 14 } xnsInmult OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 15 } xnsUnknown OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 16 } cisco MIB [Page 126] Request for Comments: Draft cisco Systems, Inc. xnsFwdbrd OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 17 } xnsEchoreqin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 18 } xnsEchoreqout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 19 } xnsEchorepin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 20 } xnsEchorepout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { xns 21 } -- the Temporary AppleTalk group atInput OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 1 } atLocal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 2 } atBcastin OBJECT-TYPE SYNTAX INTEGER cisco MIB [Page 127] Request for Comments: Draft cisco Systems, Inc. ACCESS read-only STATUS experimental ::= { appletalk 3 } atForward OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 4 } atBcastout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 5 } atFormerr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 6 } atChksum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 7 } atNotgate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 8 } atHopcnt OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 9 } atNoaccess OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 10 } cisco MIB [Page 128] Request for Comments: Draft cisco Systems, Inc. atNoroute OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 11 } atNoencap OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 12 } atOutput OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 13 } atInmult OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 14 } atRtmpin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 15 } atRtmpout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 16 } atNbpin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 17 } atNbpout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only cisco MIB [Page 129] Request for Comments: Draft cisco Systems, Inc. STATUS experimental ::= { appletalk 18 } atAtp OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 19 } atZipin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 20 } atZipout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 21 } atEcho OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 22 } atEchoill OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 23 } atDdpshort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 24 } atDdplong OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 25 } cisco MIB [Page 130] Request for Comments: Draft cisco Systems, Inc. atDdpbad OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 26 } atNobuffer OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 27 } atArpreq OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 28 } atArpreply OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 29 } atArpprobe OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 30 } atUnknown OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { appletalk 31 } -- the Temporary Novell group novellInput OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 1 } novellBcastin OBJECT-TYPE SYNTAX INTEGER cisco MIB [Page 131] Request for Comments: Draft cisco Systems, Inc. ACCESS read-only STATUS experimental ::= { novell 2 } novellForward OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 3 } novellBcastout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 4 } novellFormerr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 5 } novellChksum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 6 } novellHopcnt OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 7 } novellNoroute OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 8 } novellNoencap OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 9 } cisco MIB [Page 132] Request for Comments: Draft cisco Systems, Inc. novellOutput OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 10 } novellInmult OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 11 } novellLocal OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 12 } novellUnknown OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 13 } novellSapreqin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 14 } novellSapresin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 15 } novellSapout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS experimental ::= { novell 16 } novellSapreply OBJECT-TYPE SYNTAX INTEGER ACCESS read-only cisco MIB [Page 133] Request for Comments: Draft cisco Systems, Inc. STATUS experimental ::= { novell 17 } END 5. Identification of OBJECT instances for use with the SNMP To be written. cisco MIB [Page 134] Request for Comments: Draft cisco Systems, Inc. 6. References [1] V. Cerf, IAB Recommendations for the Development of Internet Network Management Standards. Internet Working Group Request for Comments 1052. Network Information Center, SRI International, Menlo Park, California, (April, 1988). [2] M.T. Rose and K. McCloghrie, Structure and Identification of Management Information for TCP/IP-based internets, Internet Working Group Request for Comments 1065. Network Information Center, SRI International, Menlo Park, California, (August, 1988). [3] K. McCloghrie and M.T. Rose, Management Information Base for Network Management of TCP/IP-based internets, Internet Working Group Request for Comments 1066. Network Information Center, SRI International, Menlo Park, California, (August, 1988). [4] V. Cerf, Report of the Second Ad Hoc Network Management Review Group, Internet Working Group Request for Comments 1109. Network Information Center, SRI International, Menlo Park, California, (August, 1989). [5] J.D. Case, M.S. Fedor, M.L. Schoffstall, and J.R. Davin, Simple Network Management Protocol, Internet Working Group Request for Comments 1098. Network Information Center, SRI International, Menlo Park, California, (April, 1989). [7] Information processing systems - Open Systems Interconnection - Specification of Abstract Syntax Notation One (ASN.1), International Organization for Standardization. International Standard 8824, (December, 1987). [8] Information processing systems - Open Systems Interconnection - Specification of Basic Encoding Rules for Abstract Notation One (ASN.1), International Organization for Standardization. International Standard 8825, (December, 1987). cisco MIB [Page 135] Request for Comments: Draft cisco Systems, Inc. Table of Contents 1 Introduction .......................................... 1 2 Objects ............................................... 1 2.1 Object Groupings .................................... 1 2.2 Format of Definitions ............................... 2 3 Object Definitions .................................... 3 3.1 Product Section ..................................... 4 3.2 Local Variable Section .............................. 4 3.2.1 Local System Group ................................ 5 3.2.2 Local Interface Group ............................. 25 3.2.2.1 Local Interface Table ........................... 25 3.2.3 Local IP Group .................................... 34 3.2.3.1 Local IP Address Table .......................... 34 3.2.3.2 Local IP Routing Table .......................... 38 3.2.3.3 Local IP Accounting Table ....................... 42 3.2.4 Local TCP Group ................................... 44 3.2.4.1 Local TCP Connection Table ...................... 44 3.2.5 Local cisco Terminal Server Group ................. 47 3.2.5.1 Local Terminal Server Line Table ................ 48 3.2.5.2 Local Terminal Server Line Session Table ........ 57 3.3 Temporary Variable Section .......................... 61 3.3.1 Temporary DECNET Section .......................... 61 3.3.2 Temporary XNS Section ............................. 71 3.3.3 Temporary AppleTalk Section ....................... 79 3.3.4 Temporary Novell Section .......................... 91 4 Definitions ........................................... 98 5 Identification of OBJECT instances for use with the SNMP ............................................... 134 6 References ............................................ 135 cisco MIB [Page 136]